By Bob Perry
Beneteau First 210: Standout Trailerable – Bob Perry Review
Beneteau First 210: Bob Perry's design review
Let’s go small and look at a trailerable boat. This one is from the board of Group Finot and built by Beneteau. It is a very different approach, abandoning tradition and going after speed and convenience with modern design features.
The benefit of this type of boat is the ability to move easily to exotic or semi-exotic locations for regattas. The 210 will make a great daysailer or a camp-style cruiser. While trailerable sailboats are seldom examples of refined design, the First 210 shows design innovation aimed at sparkling performance and eye appeal. This boat is also unsinkable.
With and LOA of 21 feet, the First 210 shows a modern, round bilge hull form with a very broad transom to give it dinghylike proportions. Look carefully at the plan view, deck layout or interior. Note the location of maximum beam. In most modern designs the maximum beam is located at or around station six. If you use the same system of establishing stations and break the 210′s DWL into 10 segments, you will find the max beam around station nine! There is even a curious little hook in the deck line right at station nine. The result of this shape is extreme maximization of the small volume available in 21 feet and a wide platform aft to optimize the righting moment effect of crew weight.
The extremely high-aspect-ratio centerboard is housed in an odd shaped nacelle below the hull for a board-up draft of 2 feet, 3 inches. Almost every appendage is a candidate for “ellipticalization” these days, and I find it interesting that the designers have ended this board in a sharp point. In profile, the rudder looks ridiculously small until you realize that there are in fact two rudders. They are canted outboard at 15 degrees. With this extreme distribution of beam aft a normal rudder would pull almost clear of the water at high degrees of heel. With the two rudders, when the boat is heeled one of the rudders will still be at an effective working angle with the water. This is a slick way of reducing the required draft of the rudders. Note that the draft of the twin rudders is the same as the draft of the board housing. The rudders are linked through the member at the top of the open transom.
There are no overhangs on this little packet. The bow profile shows a hint of concavity to allow some flare into the forward sections. There is also a tiny amount of tumblehome in the midsection with a moderate BWL.
The shrouds are taken to the deck edge allowing a small jib to be sheeted inside. The mainsheet sheets to a single attachment point on the cockpit sole. All halyards lead aft to jammers within easy reach of the helm. The spar is deck stepped with a hinged step. The interior is a one piece GRP molding with small sink and one burner stove. The portable head is under the V-berth. The small interior space is divided by a trunk that carries that top of the swing keel. A hinged leaf table is attached to this trunk. The four berths are all adult sized.
On deck, the swim ladder and outboard bracket fit neatly between the twin rudders. The two cockpit lockers contain a space specifically for the outboard fuel tank. The bubblelike desk is striking and set off by a varnished mahogany toerail.
The First 210 appears to combine careful styling with performance and safety. The general approach to this design is similar to the Mini-Transatlantic Class, but the boat is not as radical in proportions as a true mini-transat racer. Beneteau’s tooling of molded parts is as good as any in the business and their approach to finish and style is perhaps the best in the business. These aspects combine to ensure that the little 210 will be a standout.
|Draft||5’1″ – 2’4″|
|Sail Area||243 sq. ft.|
|Auxiliary||5 hp outboard|
The Beneteau 210 is no longer in production, but you can find used ones for sale through our Boats For Sale section.
For more information on Beneteau models, contact:
24 North Market St.
Charleston, SC 29401